Press "Enter" to skip to content

Start Searching the Answers

The Internet has many places to ask questions about anything imaginable and find past answers on almost everything.

What is mezzanine racking?

Mezzanine floor racking systems let your company optimize the vertical space of a warehouse by doubling or tripling the usable surface area. … Adding mezzanine work platforms can be the most cost-efficient way to increase warehouse storage space without the expense of a building expansion.

What is a mezzanine in a warehouse?

Warehouse mezzanine refers to an elevated section of flooring or platform that’s installed between the floor and the ceiling to serve several purposes in some warehouse operations. … Freestanding mezzanines are very flexible and have the capacity to house pallet racks and shelving systems.

What is the minimum clearance between pallets and a racking structure?

Set and enforce adequate handling clearances between pallet loads and the racking frame around them. SEMA specifies a minimum clearance of 75mm between the top of the load and the beam above and on each side. These are absolute minima and the more clearance you can allow, the safer your operation.

How much space do you need between forklift racks?

If you have a wide aisle forklift (a sit-down counterbalanced truck), generally your aisles should be 12-13 feet wide for standard 48 inch pallets. If you have narrow aisle trucks, the aisles should be 8-10 feet wide, and for very narrow aisle trucks they can be 6 feet or less.

Can you work under pallet racking?

Can you walk under pallet racking? There shouldn’t be any unsecured loads being stored on a pallet at height and a scheme of racking inspections and damage reporting should ensure that the racking is stable. Lighting may be an issue.

Do storage racks need to be bolted to the floor?

First and foremost, the Rack Manufacturers’ Institute (RMI) clearly specifies in its American National Standards that all columns of pallet racks should be anchored and secured to the floor with bolts. … The RMI put these regulations and specifications into their Standards to make sure pallet racks do not collapse.

So, Is it a Legal Requirement to have an Annual Racking Inspection? No. However, in not having an annual racking inspection, employers and warehouse owners go against HSE’s advice. This means that if an accident related to racking were to happen, they would be both legally and morally responsible.

How do you secure a pallet racking to the floor?

Insert the wedge anchors into each hole through the upright legs of the pallet racks. Carefully hammer the anchors into each hole ensuring that they are installed to the desired depth. Tighten all the nuts using a torque wrench to ensure they are tightened to the required torque value.

Does pallet racking need to be certified?

Pallet Racking system also known as steel storage systems installed in a workplace require regular inspection with compulsory annual audit and certification. If you are unsure about your Pallet Racking inspection due date or the entire certification process, you can leave your worry on us.

How do wedge anchor bolts work?

The wedge anchor is inserted into a hole in concrete until the threads are below the surface of the concrete. The nut and washer are placed on the threads and tightened until finger tight. Using a wrench, the nut is then turned, which pulls the anchor up to wedge the clip between the stud and the wall of the concrete.

How much weight can a sleeve anchor hold?

200 pounds

Can sleeve anchors be removed?

Removing sleeve anchors and strike anchors Like other male anchors, sleeve anchors and strike anchors can‘t be fully removed, although some sleeve anchors can simply be tapped below the surface of the concrete after removing the nut and washer.

How do you use a sleeve anchor in concrete?

Installation Instructions for the Concrete Sleeve Anchor Clean out the hole of all debris. Set the nut flush with the top of the sleeve anchor. Insert the sleeve anchor through the fixture into the hole in the base material until the washer and nut is tight against the fixture. Turn the nut until finger tight.

What are sleeve anchors for?

Sleeve anchors are versatile. They can be used for light or heavy-duty fastening so can be applied in projects such as fixing radiators in the home but also work for much larger operations such as securing the joists of decking. These anchors can be used in a variety of base materials such as concrete, brick and block.

Can you use sleeve anchors in Brick?

Sleeve anchors are versatile and can be used in solid brick, brick with holes or the mortar joint. … The hole that is required to be drilled into the brick is the same diameter as the sleeve anchor being used. A hammer drill with a carbide tip must be used to drill the hole in the brick.

Can you drill into concrete with an impact driver?

Can I Drill With an Impact Driver? If you‘re drilling holes at 1/4-inch or under, you‘ll be able to drill through brick and some concrete with an impact driver. Impact drivers have a freakish amount of torque, but they are not designed to be used like a regular drill or hammer drills.

Can you drill into concrete with a regular drill?

You can drill holes in concrete with a regular drill. … You will need a bit more patience and a wider array of drill bits when using a regular drill, but the procedure is the same for drilling in concrete regardless if you use a regular drill or a hammer drill.